Software/Firmware for Fusion Edge Laser Systems

Fusion Edge

Firmware & Driver Downloads

Signup to receive email notification when a new driver or firmware is available for your laser model.

Epilog Software Suite 2.2.9.0

Download 64-bit (x64) Version
Download 32-bit (x86) Version

Epilog Software Suite 2.2.9.0 (8/27/2021)

Everything you need to run your Fusion Edge system
Installs the Epilog Job Manager and the Epilog Laser Dashboard

Version 2.2.9.0 Release Notes

Adding new engravers to the Job Manager is more intuitive
Bug fixes and improvements

- For more information on the Job Manager, click here.
- Download Software Suite install and use instructions.
- For information on how to use the Construction Lines feature, click here

Please note: Remove previous version of Epilog Job Manager and Epilog Software Suite before installation! (Go to Control Panel > Programs and Features and remove the software.)

Download 64-bit (x64) Version Download 32-bit (x86) Version

Minimum Requirements:

Windows 7, Windows 8.1, or Windows 10
Operating system should have all system updates before installation
Support for OpenGL 3.0 (or higher) or OpenGL 2.0ES (or higher)
4GB RAM or more
2 processor cores or more
Processor can be any Intel i3/i5/i7, AMD Ryzen 3/5/7, AMD A4/A6/A8/A10/A12/FX
Integrated gigabit ethernet required for Fusion M2 vision system. Fusion Pro/Edge does not have the same requirement, but is nice to have.

Recommended Specifications:

8GB RAM or more
4 processor cores or more
Processor can be any Intel i5/i7, AMD Ryzen 5/7, AMD A6/A8/A10/A12/FX

1.0.4.2 Firmware Downloads

1.0.4.2 (.SWU)
1.0.4.2 (.ZIP)

Firmware: 1.0.4.2 (9/9/2021)

Please note: After upgrading the Fusion Edge to 1.0.4.2, you cannot downgrade to a version below 1.0.4.0.

Download Firmware 1.0.4.2 Download Firmware 1.0.4.2 (.zip)

Read Install Instructions

NEW FEATURES/ENHANCEMENTS

Table can now be nudged when the machine is running. (New as of 1.0.3.6)
Improved engraving quality of the Rotary Attachment. (New as of 1.0.3.6)
Enabled the following features on the Fusion Pro 24/36: (New as of 1.0.3.6)
- WiFi Capabilities
- Job thumbnails at machine (requires newest Software Suite)
- Edit job settings at the machine
- Adjusted the Rotary Attachment’s park position for easier loading and unloading
Enabled the following features on the Fusion Pro 24/36: (New as of 1.0.4.1)
- Stack (Processing) Light
- Ability to control the Air Assist from the Software Suite
- Carriage camera for registration
Improved vector speed and power compensation. (New as of 1.0.3.6)
Power and Frequency can be modified while the job is running, dependent on job and laser type. (New as of 1.0.4.1)
Added dynamic raster ramps for improved raster speeds and the ability to disable this feature in the settings menu. (New as of 1.0.4.1)

BUG FIXES:

Miscellaneous bug fixes and enhancements

FIRMWARE FAQ'S:

How do I know what firmware version I have?
- If you have older firmware, you can determine your firmware version under Settings (gear icon) > Version on the control panel. If your firmware version is newer, it will be listed at the bottom of the settings menu.
How often will I receive firmware updates?
- If you have signed up for firmware updates, we only send new versions to customers when there are feature updates or large bug fixes. Incremental changes are only released to new production machines, and don't need to be updated in your machine if you are not experiencing issues.